search
Differences
This shows you the differences between two versions of the page.
|
ebike:tsdz2 [2018/07/09 10:47] shaddi |
ebike:tsdz2 [2021/02/24 23:49] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | https://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/stsw-link004.html | ||
| - | **Random TSDZ2 notes** | ||
| - | |||
| - | <code> | ||
| - | echo "00 00 ff 20 df 00 ff 00 ff 00 ff 00 ff 00 ff" | xxd -r -p > option_bytes_pwm_n_channels_enabled.bin | ||
| - | stm8flash -c stlinkv2 -p stm8s105?6 -s opt -w option_bytes_pwm_n_channels_enabled.bin | ||
| - | stm8flash -c stlinkv2 -p stm8s105?6 -w LCD3_TSDZ2_firmware_v3.bin | ||
| - | |||
| - | stm8flash -c stlinkv2 -p stm8s105?4 -w TSDZ2_improved_original_firmware-v3.bin | ||
| - | stm8flash -c stlinkv2 -p stm8s105?4 -s eeprom -w TSDZ2_48V_original_firmware_eeprom.bin | ||
| - | stm8flash -c stlinkv2 -p stm8s105?4 -s opt -w TSDZ2_48V_original_firmware_option_bytes.bin | ||
| - | </code> | ||
| - | |||
| - | |||
| - | **ISP-Connector** | ||
| - | <code> | ||
| - | 1 VCC | ||
| - | 2 SWIM | ||
| - | 3 GND | ||
| - | 4 RST | ||
| - | </code> | ||
| - | |||
| - | |||
| - | ** XH18 LCD wiring ** | ||
| - | |||
| - | https://www.displayfuture.com/Display/datasheet/controller/ST7735.pdf | ||
| - | |||
| - | https://warmcat.com/2016/08/26/st7735-tft-lcd-goodness.html | ||
| - | |||
| - | <code> | ||
| - | 1 LED-K | ||
| - | 2 LED-A | ||
| - | 3 GND | ||
| - | 4 VDD | ||
| - | 5 TE | ||
| - | 6 NC | ||
| - | 7 /CS | ||
| - | 8 /RESET | ||
| - | 9 RS | ||
| - | 10 /WR | ||
| - | 11 /RD | ||
| - | 12 D7 | ||
| - | 13 D6 | ||
| - | 14 D5 | ||
| - | 15 D4 | ||
| - | 16 D3 | ||
| - | 17 D2 | ||
| - | 18 D1 | ||
| - | 19 D0 | ||
| - | 20 GND | ||
| - | </code> | ||
| - | |||
| - | |||
| - | {{:ebike:tsdz2-plug.jpg?nolink&400|}} | ||
| - | |||
| - | **LCD-Connector** | ||
| - | |||
| - | https://opensourceebikefirmware.bitbucket.io/kunteng_lcd3/LCD3_on_TSDZ2--Wire_KT-LCD_to_TSDZ2.html | ||
| - | |||
| - | <code> | ||
| - | black: GND (battery -) | ||
| - | green: VCC (battery +) | ||
| - | white: signal from LCD to motor to enable the controller, (VCC-0.9V, perhaps through an input diode in the LCD) | ||
| - | purple: brake switch / motor cut off when connected to GND | ||
| - | brown: serial data from motor/controller to LCD | ||
| - | orange: serial data from LCD to motor/controller | ||
| - | </code> | ||
| - | |||
| - | |||
| - | |||
| - | **Speed sensor Connector** | ||
| - | <code> | ||
| - | orange: GND | ||
| - | brown: 5V (controller MCU supply voltage) | ||
| - | green: headlight 6V | ||
| - | white: speed sensor input (with pullup resistor to 5V) | ||
| - | black: SWIM | ||
| - | purple: RESET | ||
| - | </code> | ||
